- Page ID
Geologic folds are layers of rock that are curved or bent by ductile deformation. Folds are most commonly formed by compressional forces at depth, where hotter temperatures and higher confining pressures allow ductile deformation to occur.
Folds are described by the orientation of their axes, axial planes, and limbs. The plane that splits the fold into two halves is known as the axial plane. The fold axis is the line along which the bending occurs and is where the axial plane intersects the folded strata. The hinge line follows the line of greatest bend in a fold. The two sides of the fold are the fold limbs.
Symmetrical folds have a vertical axial plane and limbs have equal but opposite dips. Asymmetrical folds have dipping, non-vertical axial planes, where the limbs dip at different angles. Overturned folds have steeply dipping axial planes and the limbs dip in the same direction but usually at different dip angles. Recumbent folds have horizontal or nearly horizontal axial planes. When the axis of the fold plunges into the ground, the fold is called a plunging fold. Folds are classified into five categories: anticline, syncline, monocline, dome, and basin.
Anticlines are arch-like, or A-shaped folds that are convex-upward in shape. They have downward curving limbs and beds that dip down and away from the central fold axis. In anticlines, the oldest rock strata are in the center of the fold, along the axis, and the younger beds are on the outside. Since geologic maps show the intersection of surface topography with underlying geologic structures, an anticline on a geologic map can be identified by both the attitude of the strata forming the fold and the older age of the rocks inside the fold. An antiform has the same shape as an anticline, but the relative ages of the beds in the fold cannot be determined. Oil geologists are interested in anticlines because they can form oil traps, where oil migrates up along the limbs of the fold and accumulates in the high point along the fold axis.
Synclinal fold – Macigno Formation by alanpitts on Sketchfab
Synclines are trough-like, or U shaped, folds that are concave-upward in shape. They have beds that dip down and in toward the central fold axis. In synclines, older rock is on the outside of the fold and the youngest rock is inside of the fold axis. A synform has the shape of a syncline but like an antiform, does not have distinguishable age zones.
Monoclines are step-like folds, in which flat rocks are upwarped or downwarped, then continue flat. Monoclines are relatively common on the Colorado Plateau where they form “reefs,” which are ridges that act as topographic barriers and should not be confused with ocean reefs (see Chapter 5). Capitol Reef is an example of a monocline in Utah. Monoclines can be caused by bending of shallower sedimentary strata as faults grow below them. These faults are commonly called “blind faults” because they end before reaching the surface and can be either normal or reverse faults.
A dome is symmetrical to semi-symmetrical upwarping of rock beds. Domes have a shape like an inverted bowl, similar to an architectural dome on a building. Examples of domes in Utah include the San Rafael Swell, Harrisburg Junction Dome, and Henry Mountains [2; 3]. Domes are formed from compressional forces, underlying igneous intrusions  (see Chapter 4), by salt diapirs, or even impacts, like upheaval dome in Canyonlands National Park.
A basin is the inverse of a dome, a bowl-shaped depression in a rock bed. The Uinta Basin in Utah is an example of a basin. Some structural basins are also sedimentary basins that collect large quantities of sediment over time. Sedimentary basins can form as a result of folding but are much more commonly produced in mountain building, forming between mountain blocks or via faulting. Regardless of the cause, as the basin sinks or subsides, it can accumulate more sediment because the weight of the sediment causes more subsidence in a positive-feedback loop. There are active sedimentary basins all over the world . An example of a rapidly subsiding basin in Utah is the Oquirrh Basin, dated to the Pennsylvanian-Permian age, which has accumulated over 9,144 m (30,000 ft) of fossiliferous sandstones, shales, and limestones. These strata can be seen in the Wasatch Mountains along the east side of Utah Valley, especially on Mt. Timpanogos and in Provo Canyon.
2. Gilbert GK, Dutton CE (1877) Report on the geology of the Henry Mountains. U.S. Government Printing Office, Washington
3. Ressetar R (2013) The San Rafael Swell and Henry Mountains Basin: geologic centerpiece of Utah. Utah Geological Association, Utah Geological Association
4. Coleman JL, Cahan SM (2012) Preliminary catalog of the sedimentary basins of the United States. U.S. Geological Survey