Skip to main content
Geosciences LibreTexts

6.5: Groups, Formations, and Members

  • Page ID
    6623
  • Geologists who study sedimentary rocks need ways to divide them into manageable units, and they also need to give those units names so that they can easily be referred to and compared with other rocks deposited in other places. The International Commission on Stratigraphy (ICS) has established a set of conventions for grouping, describing, and naming sedimentary rock units.

    The main stratigraphic unit is a formation, which according to the ICS, should be established with the following principles in mind:

    The contrast in lithology between formations required to justify their establishment varies with the complexity of the geology of a region and the detail needed for geologic mapping and to work out its geologic history. No formation is considered justifiable and useful that cannot be delineated at the scale of geologic mapping practiced in the region. The thickness of formations may range from less than a meter to several thousand meters.

    In other words, a formation is a series of beds that is distinct from other beds above and below, and is thick enough to be shown on the geological maps that are widely used within the area in question. In most parts of the world, geological mapping is done at a relatively coarse scale, and so most formations are in the order of a few hundred metres thick. At that thickness, a typical formation would appear on a typical geological map as an area that is at least a few millimetres thick.

    A series of formations can be classified together to define a group, which could be as much as a few thousand metres thick, and represents a series of rocks that were deposited within a single basin (or a series of related and adjacent basins) over a few million to a few tens of millions of years.

    In areas where detailed geological information is needed (for example, within a mining or petroleum district) a formation might be divided into members, where each member has a specific and distinctive lithology. For example, a formation that includes both shale and sandstone might be divided into members, each of which is either shale or sandstone. In some areas, where particular detail is needed, members may be divided into beds, but this is only applicable to beds that have a special geological significance. Groups, formations, and members are typically named for the area where they are found.Home

    Upper-Cretaceous-Nanaimo-Group-rocks.png
    Figure 6.5.1 The distribution of the Upper Cretaceous Nanaimo Group rocks on Vancouver Island, the Gulf Islands, and in the Vancouver area. [Image Description]

    The sedimentary rocks of the Nanaimo Group provide a useful example for understanding groups, formations, and members. During the latter part of the Cretaceous Period, from about 90 Ma to 65 Ma, a thick sequence of clastic rocks was deposited in a foreland basin between what is now Vancouver Island and the B.C. mainland (Figure 6.5.1). The Nanaimo Group strata comprise a 5000-metre-thick sequence of conglomerate, sandstone, and mudstone layers. Coal was mined from Nanaimo Group rocks from around 1850 to 1950 in the Nanaimo region, and even more recently in the Campbell River area.

    The Nanaimo Group is divided into 11 formations as described in Table 6.6.  In general, the boundaries between formations are based on major lithological differences. As can be seen in the far-right column of Table 6.6, a wide range of depositional environments existed during the accumulation of the Nanaimo Group rocks, from nearshore marine for the Comox and Haslam Formation, to fluvial and deltaic with backwater swampy environments for the coal-bearing Extension, Pender, and Protection Formations, to a deep-water submarine fan environment for the upper six formations.
    Table 6.6 The formations of the Nanaimo Group[1]
    [Skip Table 6.6]
    Approximate Age (Ma) Formation name Lithologies Depositional Environment
    65 to 66 Gabriola Sandstone with minor mudstone Submarine fan, high energy
    66 to 67 Spray (Fine grained) Mudstone/sandstone turbidites Submarine fan, low energy
    67 to 68 Geoffrey Sandstone and conglomerate Submarine fan, high energy
    68 to 70 Northumberland (Fine grained) Mudstone turbidites Submarine fan, low energy
    70 De Courcy Sandstone Submarine fan, high energy
    70 to 72 Cedar District (Fine grained) Mudstone turbidites Submarine fan, low energy
    72 to 75 Protection Sandstone and minor coal Nearshore marine and onshore deltaic and fluvial
    75 to 80 Pender Sandstone and minor coal Nearshore marine and onshore deltaic and fluvial
    80 Extension Conglomerate, with minor sandstone and some coal Nearshore marine and onshore deltaic and fluvial
    80 to 85 Haslam (Fine grained) Mudstone and siltstone Shallow marine
    85 to 90 Comox Conglomerate, sandstone, mudstone (coal in the Campbell River area) Nearshore fluvial and marine

    In tables like this one, the layers are always listed in order, with the oldest at the bottom and the youngest at the top.

    The five lower formations of the Nanaimo Group are all exposed in the Nanaimo area, and were well studied during the coal mining era between 1850 and 1950. All of these formations (except Haslam) have been divided into members, as that was useful for understanding the rocks in the areas where coal mining was taking place.  Within some of those members even some individual beds have been named if they were of specific importance to the mining industry.

    Although there is a great deal of variety in the Nanaimo Group rocks, and it would take hundreds of photographs to illustrate all of the different types of rocks, a few representative examples are provided in Figure 6.5.2.

    Alternating layers of light and dark rock of various textures
    Figure 6.5.2a Representative photos of Nanaimo Group rocks. Turbidite layers in the Spray Formation on Gabriola Island. Each turbidite set consists of a lower sandstone layer (light colour) that grades upward into siltstone, and then into mudstone. (See Figure 6.4.2 for detail.)
    A tall, light coloured rock wall with a black streak running through the middle.
    Figure 6.5.2b Two separate layers of fluvial sandstone with a thin (approx. 75 centimetres) coal seam in between. Pender Formation in Nanaimo.

    Looks like smooth black rocks stuck into cement and worn flat.
    Figure 6.5.2c Comox Formation conglomerate at the very base of the Nanaimo Group in Nanaimo. The metal object is the end of a rock hammer that is 3 centimetres wide. Almost all of the clasts in this view are well-rounded basalt pebbles cobbles eroded from the Triassic Karmutsen Formation which makes up a major part of Vancouver Island.

    Image Descriptions

    HomeFigure 6.5.1 image description: A map showing that Nanaimo Group rocks are present along the east coast of Vancouver Island from Nanaimo to Campbell River, farther inland in areas around Port Alberni and Duncan, on much of the Gulf Islands and a bit in the Vancouver area. [Return to Figure 6.5.1]

    Media Attributions

    • Figure 6.5.1: Redrawn based on Mustard, P., 1994, The Upper Cretaceous Nanaimo Group, Georgia Basin, in J. Monger (ed) Geology and Geological Hazards of the Vancouver Region, Geol. Survey of Canada, Bull. 481, pp. 27-95. © Steven Earle. CC BY.
    • Figure 6.5.2abc: © Steven Earle. CC BY.

    1. [Based on data in Mustard, P., 1994, The Upper Cretaceous Nanaimo Group, Georgia Basin, in J. Monger (ed) Geology and Geological Hazards of the Vancouver Region, Geol. Survey of Canada, Bull. 481, p. 27-95.]